How to Find and Fix a Hole in Air Mattress? Simplest Solution!

A little hole in the air mattress might give you a tough time, especially when you go out camping or for a picnic.

Sometimes, you pass the entire day searching the hole to fix that but fail to do so. Now, the only question pops into your head, which is how to find and fix a hole in air mattress?

Don’t worry at all; from this writing, you’ll get some quick methods to locate the hole in your air mattress, and that too, without burning the midnight oil.

So, stay tuned if you don’t want to ruin your camping party anymore!

A Few Tips Before Starting to Find The Holes

Before jumping onto the methods of finding the holes, there are some works that you’ll need to do.

  • Always make sure to mark the leakage parts with the help of duct tape or a piece of marker.
  • Remember to dry the mattress thoroughly in direct sunlight. Also, keep it in a place where sufficient lighting is present for an adequate and clear vision.
  • Inflate and deflate the mattress at a snail’s pace so that it won’t burst out (though some of the manufacturers warn to do this). Be sure to handle the mattress without making it wet.

Easiest Methods of Finding Holes in Air Mattress

So, after accomplishing the above-written task, let’s move on to the simplest methods of locating holes in an air mattress. Don’t skip any part!

  • Method-1:Valve and Seam Visual Inspection

Most of the leaks occur from either the valve or the seam areas of an air mattress. So, it’s a smart decision to check them properly at first.

Besides, the valve can’t be fixed if it has a got major problem. However, you can always patch the smaller issues, like the plugging problems for sealing the stem of the valve, just by placing a thin plastic piece.

Be sure to insert the plug into the stem of the valve to seal the air from flowing out. After that, you should start checking the seam areas carefully for leaks.

  • Method-2: Use Ear to Hear

Yep. Your ears are useful when it comes to checking for leaks in your mattress as it captures the sound coming out from the leaks. The hissing sound will appear from the stuff to your sensitive ear, assisting you to locate the smaller holes in the right way.

First off, remove the bedsheet from the mattress before inflating it with air. Then, start the inflation, but be careful as the overflow of air might burst the mattress. In that case, you can either use your breath for inflation.

Start with the seam area to check for the holes and use your hands to apply adequate amounts of pressure. Make your head moves around the surface to find the escaping air that’s coming out from your mattress.

After that, mark the holes using a permanent marker. On the flip side, you can use duct tape as well to make those marks more noticeable.

  • Method-3: Use Hands to Feel the Escaping Air

Your hands can play a vital role in detecting the leak of the air. Slowly move your palm around the surface to feel the air pressure coming out from the mattress.

For ensuring a better sense of the air, use wet hands instead of dry ones, and you’ll feel the “cold air sensation” or something like that in your palms.

Don’t move your hands too quickly, or else you might miss the soft and subtle flow of the escaping air. Again, you have to mark those spots right away through duct tape or a permanent marker.

  • Method-4: Utilizing a Tissue Paper

Tissue paper or napkin comes in handy to make the job done for your inspection of the holes in the air mattress. In order to check holes properly, lay the tissues flat on the surface after inflation and start applying pressure all around the mattress to guide the air from flowing in the areas where you want them to work.

Move the tissue papers slowly around the mattress (especially on the seams as they’re a common source of leaks) and observe carefully if any interferences are occurring or not. Don’t even miss the slightest sound of the escaping air.

Do this on the top, bottom, and sides of your mattress to get the sound of air making a connection with the paper while it’s over the leakage areas.

Guess what? Bigger leaks might cause the movement of the tissue. So, after finding the leaks, don’t forget to mark those areas for patching them later on.

The Way of Fixing the Holes – Simplest Solution

Usually, a hole or a small tear causes the air to leak. But in some rare cases, the leak comes from a gasket that has been damaged. The strategies of finding the holes are already discussed earlier, now let’s talk about the solution.

Patching the Leak

Patching can be done through different methods, let’s say, with the patch kit provided by the manufacturers. Using the makers’ patch kit is pretty simple. You’ll just have to follow the instructions of the kit, and that’s it.

And a DIY method is relatively hard at times, depending on the type of leaks.

In order to start patching the mattress, it should be fully deflated, sealed, clean, and dry. After that, jump to the surface area and lay it flat to make sure every leak is visible.

For a simple patch, you must have to attach a strong adhesive to the leak areas. In this case, a bandage-type patch can be attached directly on the top of the leaks since it doesn’t require any additional adhesives.

Use layers to coat the adhesive chemical for stronger bonds. Add a single layer first, and then apply the second one. Sometimes, depending on the size of the hole, a third layer can be applied as well. But it’s a rare case.

Tips

  • If you are using a vinyl adhesive, then make sure to put on the gloves before applying the glue on the leaking parts. The chemical might be toxic and too risky for your health.
  • Vinyl adhesive takes a couple of minutes or so to dry after coating. So, if you’re preparing for the second coating, be sure to wait for a while until it dries completely.

After patching with the glue, apply the force of heavy objects to prevent the edges from curling or curving. Then, let it get dry for more than 7 hours.

Finally, after drying out, test the mattress by inflating it. But perform this task smoothly and carefully. Otherwise, it might end up bursting again.

Final Words

Now you know how to find and fix a hole in air mattress permanently with the assistance of a DIY patch or with a patch kit. Make sure to apply the abovementioned techniques to fix those problems within no time. So hopefully, your next camping trip is going to be awesome!

Leave a Comment